Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Blog Article
Do not undervalue the forklift at work. If the procedure is bad, there will be major mishaps in mins, and there are several accidents involving forklifts.
Situation 1: The forklift freight obstructed the driver's sight, and the person in front might not be discovered, leading to a moving crash.
Instance 2: In order to maintain the equilibrium of the forklift when lifting hefty items, the employees used their body weight as the weight, which almost caused casualties.
Situation 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not put on the seat belt, the forklift lifter drops and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.
Begin.
1. Prior to beginning, observe the surroundings, and after confirming that there are no barriers that impede the security of driving, honk the horn initially and afterwards begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure before beginning.
3. When the forklift begins with a load, the vehicle driver ought to first verify that the load is secure and trustworthy.
4. The start has to be slow and constant.
Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast should be slanted backward. .
2. Do not raise the fork too high when driving. When getting in and leaving the job website or while driving, be careful that there will certainly be no obstacles overhead. When the load is traveling, the fork must not be increased expensive, which will certainly impact the security of the forklift. .
3. After unloading, the fork must be reduced to the typical driving placement before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and tip over. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is restricted to brake suddenly while driving with loads unless there are unique circumstances.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and must keep a specific security distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the lowest setting that does not prevent the driving, and the gantry should be correctly tilted back. The tons will not be elevated other than when piling or packing. .
8. The height of the load need to not block the motorist's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving rate of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when entering the production workshop area. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to depend on the fork to hold products and play a stabilizing role. .
12. If problems are located, they will be repaired and reported in a timely fashion, and they will never run with diseases or conceal them.
filling and discharging.
1. When Stand-on Electric Pallet Stacker fork-loading things, the range between both forks must be changed as needed to make the tons of the two forks well balanced and not skewed, and one side of the item must protest the rack. .
2. It is restricted to deal with a solitary fork Stand-on Electric Pallet Stacker or utilize a fork top or pull. In unique scenarios, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea should not touch various other items or objects. The tons should be supported with very little back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is lowered to permit easy placement of the lots and extraction of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Straining is prohibited, and it is restricted to utilize forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to utilize the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.
Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .
Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and progress, if they encounter big or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844